Sherwood RX-773 Instrukcja Naprawy

10Front Panel Controls3164212221 11 9 5671715 188 12 13 14 19 2010󳂮FLUORESCENT DISPLAY1. Input, frequency, volume level, operating information, etc.2.

11󳂮AUX 1, 2 IN JACKS• The AUX 1, 2 IN jacks can be connected to additional audiocomponents such as an MP3 player, etc.󳂮Note :• When connecting these j

ENGLISH12Universal Remote ControlsThis universal remote control can operate not only this receiver but also most popular brands of audio and video com

ENGLISH13󳂮FUNCTION TABLE of the NUMBERED BUTTONS.󳂮Notes :• Some functions for each component may not be available or may work differently.• Depending

ENGLISH14LOADING BATTERIESOPERATING COMPONENTS WITH REMOTE CONTROLREMOTE CONTROL OPERATION RANGE󳂮In case that this remote control emits the infrared b

ENGLISH15USING FUNCTIONS OF REMOTE CONTROLEntering a setup code• This remote control can control up to 8 different components.• Before operating audio

ENGLISH16• If any of buttons fails to operate as they should, start fromthe step 1 again to enter the correct setup code.󳂮Note :• Manufacturers may us

ENGLISH17• If the command has been learned successfully, "OK" isdisplayed and then "SEL" is flickering.• If "ERROR" is d

ENGLISH18Erasing the programmed command from one button• "OK" is displayed and then "SEL" is flickering.• Then "BTTN" is

ENGLISH19Programming a macro functionExample : When playing a CD on the CD player connectedto CD jacks of this receiver.①. Press "AUDIO" but

ENGLISH21. Read these instructions.2. Keep these instructions.3. Heed all warnings.4. Follow all instructions.5. Do not use this apparatus near water.

ENGLISH20Operating a macro function󳂮Notes:• The codes programmed into a MACRO button will be transmitted at aninterval of 0.5 seconds. However, some c

ENGLISH211. Perform the steps 3 and 4 in "Entering a setup code"procedure on page 15 to select a master device andthe punch-through mode (&q

ENGLISH223. While the device is displayed, press the CURSORUP(▲)/DOWN(▼) buttons to select the one punch-through deleting mode ("DELETE"), t

23ENGLISHChanging the transmission signal• This remote control can emit not only the infrared beams which the conventional remote control uses but als

ENGLISH24OperationsLISTENING TO A PROGRAM SOURCEBefore operation• Push the POWER switch.• This unit enters the standby mode and the POWERON/STANDBY bu

25ENGLISH• Be sure to switch off all the speakers installed in the mainroom.󳂮Note : Be careful not to set the volume too high whenusing headphones.• E

󳂮When adjusting the bass󳂮When adjusting the trebleENGLISH26Adjusting the sound volume balance• “TON DIR” is displayed, “DIRECT” lights up and the soun

27ENGLISHLISTENING TO RADIO BROADCASTSAuto tuning• Each time this button is pressed, the tuner is automaticallyselected and the band is changed as fol

ENGLISH28󳂮MEMORY BACKUP FUNCTIONThe following items, set before the receiver is turned off, are memorized.• INPUT SELECTOR settings• Preset stations,e

29ENGLISH1. Press the BAND button or the TUNER button repeatedlyto select XM mode.2. Press the TUNING UP(▲, +)/ DOWN(▼, -) buttonsrepeatedly to select

3ENGLISHIntroductionThis symbol is intended to alert the user to the presence ofuninsulated "dangerous voltage" within the product'senc

ENGLISH30Examples: For "3" :For "27" : For "124" : • When "XM - - -" disappears, repeat again from theabov

31ENGLISH1. Select the desired channel with preforming channelsearch, direct search or category search.2. To memorize the channels, perform the steps

ENGLISH32RECORDINGRecording with TAPE• The volume, tone(bass, treble) and balance settings have no effect on the recording signals.• When you select t

33ENGLISH• Each time the POWER ON/STANDBY button on the frontpanel is pressed, the ROOM2 mode changes as follows :R2 > OFF : ROOM2 off mode("

ENGLISH345. Start play on the component related to the ROOM2source. • While the mute function for ROOM2 is operating, "R2" isflickering.• To

ENGLISH35Troubleshooting GuidePROBLEM POSSIBLE CAUSE REMEDYIf a fault occurs, run through the table below before taking your receiver for repair.If th

36ENGLISHSpecifications󳂮 AMPLIFIER SECTION• Power output, 8Ω, THD 0.7 %, 20 Hz~20 kHz, only a pair of speakers driven | 2 X 100 W• Total harmon

37ENGLISHSetup Code TableAOC 005 003Admiral 041 031Aiko 014Akai 005Alaron 026Ambassador 024America Action 027Ampro 043Anam 027 047 048 049Audiovox 030

38ENGLISHAdmiral 027 021Adventura 000Aiko 025Aiwa 005 000Akai 026America Action 025America High 004Asha 023Audiovox 005Beaumark 023Bell & Howell 0

39ENGLISHVCR-TV/VCRHeadquarter 011Hitachi 000 008 026JVC 014 026Jensen 026KEC 005 025KLH 015Kenwood 014 026 006Kodak 004 005LXI 005Lloyd’s 000Logik 01

ENGLISH4CONTENTSIMPORTANT SAFETY INSTRUCTIONS ...

40ENGLISHHQ 000Lloyds 000MGA 023Megavox 016 (TV use 010) 004 (TV use 008)000Magnin 023Memorex 005 028 (TV use 042)Mitsubishi 027 (TV use 041)Orion 001

41ENGLISHHitachi 006 107 074Insight 085Jasco 010 018 021Jerrold 002 007 033 032 009 010006 034 035 036 037 041042 043 082 085 107Magnavox 043 045 080

ENGLISH42GE 043Lutron 044One For All 042Radio Shack 043Security System 042Universal X10 042X10 042Aiwa 045 029Fisher 005Harman/Kardon 046JBL 046JVC 04

43ENGLISHAiwa 010 030Burmester 019California Audio Lab002Carver 010 012 020DKK 001Denon 028 034Emerson 035Fisher 012 033Garrard 019 018Genexxa 004 035

5System ConnectionsENGLISH• Please be certain that this unit is unplugged from the AC outlet before making any connections.• Be sure to observe the co

ENGLISH6CDCD playerTape deck, MD recorder, etc.• The AUX jacks may also be connected to an additional component.• The DVD jacks may be connected to AU

7ENGLISH4. CONNECTING SPEAKERS • You can connect up to four pairs of speakers to this receiverand select the various combinations of speakers accordin

ENGLISH87. CONNECTING MULTI-ROOM SYSTEM KIT• The multi-room system kit(sold separately ) is essential for operation from a remote location .For inform

ENGLISH98. CONNECTING PC FOR UPGRADES• This receiver incorporates RS-232C terminal that may beused in the future to update the operating software so